Vermeil and Gold Plating Specs for sizing Guide
Vermeil means a gold layer of at least 2.5 microns over sterling silver, and the US market reads that number as a material claim rather than a finish note. Below 2.5 microns the piece is gold-plated, not vermeil, and the word cannot be used, which is how the Vermeil Upgrade account reads it at USD 60-336.
We run 3 microns on sizing Guide for accounts that publish the claim, with a palladium strike layer so wear-through reads white and not yellow. Thickness is logged per lot and appears on the GRA report batch sheet, with GRA report and retail box with care card stated on the same sheet.
The cost difference is real: the USD 60-336 band moves up roughly sixty percent against rhodium-finished silver, and the retail price has to carry that or the margin disappears in the second season when the plating shows wear.
Sample to Container: The Real Calendar in the Vermeil Upgrade Program
A US buyer of sizing Guide sent us a competitor's sizing Guide in September with one question: why does this fail at prong geometry after a season. We measured it, rebuilt the spec around stone retention after a 40-cycle wear test and prong tip height within +/-0.10 mm, and shipped 100 sizing Guide that cleared inspection with zero rejects, with GRA report and retail box with care card stated on the same sheet.
The bench did not miss the defect, it was never asked to look for it. Prong geometry was absent from the purchase order, and a defect that is not named cannot be rejected on arrival, quoted at USD 60-336 per piece in retail box with care card.
The rebuild held the USD 60-336 quote and changed the plating log, the gauge and the tray rule. Second run shipped retail box with care card with zero rejects.
Three Failures That Reach the Vermeil Upgrade Bench
prong geometry
A prong that grips the girdle instead of the pavilion survives the showroom and fails the third ultrasonic clean. The seat has to be cut to the pavilion angle before the prongs close, on a 100-piece Vermeil Upgrade order at USD 60-336.
In a 100-piece run this typically shows on 14 of pieces. Catching it means measuring stone retention after a 40-cycle wear test at the tray level, not inspecting the finished carton, and 100 pieces leaves Wuzhou in retail box with care card at USD 60-336.
rhodium burn-off
A 0.05 micron rhodium layer reads white in the tray and shows yellow at the shank in six months of daily wear. Thickness, not bath chemistry, is the variable that matters, shipped as retail box with care card and certified GRA report.
The commercial effect is a return shipment plus a resize labor claim, typically USD 9-14 per piece. Buyers who have seen it once put it in the purchase order; buyers who have not usually discover it on the first return, and at USD 60-336 for 100 pieces that is the number the buyer signs.
size-step drift
A run gauged at size 6 and estimated elsewhere ships a size 8 that measures 7.75. The mismatch shows up as a resize queue two weeks after launch, which the Vermeil Upgrade file records at USD 60-336 in retail box with care card.
Our countermeasure is a gauge and a written limit. It adds about 22 seconds per piece and removes the defect from the run rather than from the carton, priced at USD 60-336 for the 100-piece Vermeil Upgrade run.
Cost Split on a Vermeil Upgrade Piece at USD 60-336
Buyers assume the stone dominates the cost of a sizing Guide. At wholesale it is closer to a quarter, and the labor line is where two quotes for the same drawing diverge by double digits, and at USD 60-336 for 100 pieces that is the number the buyer signs.
| Cost line | Share | What moves it |
|---|---|---|
| Base metal or alloy for sizing Guide | 32% | Alloy choice and casting yield |
| Stone or melee for sizing Guide | 23% | Sieve range and lot batching |
| Setting and finishing labor for sizing Guide | 21% | Jig design and bench minutes |
| Plating, polish and QC for sizing Guide | 14% | Per-tray versus per-piece checks |
| Packaging for sizing Guide | 10% | retail box with care card |
The cheapest quote for sizing Guide usually hides its saving in the plating line and the stone grade. Both show up in the second season, not the first, which is USD 60-336 on the Vermeil Upgrade schedule.
Four Spec Lines a Vermeil Upgrade Buyer Checks
A Vermeil Upgrade quote that states only metal and stone size leaves prong geometry undefined, and undefined is what gets rejected on arrival, on a 100-piece Vermeil Upgrade order at USD 60-336.
| Spec point | Common trade output | HOLYCOME standard | Cost if missed |
|---|---|---|---|
| Plating thickness | Nominal only | 0.20 micron rhodium logged per lot, 3 microns on vermeil | Wear-through inside one season |
| Surface porosity after polish | Seen after plating | Cast porosity checked before plating, rejects pulled at that stage | Plating blister six weeks later |
| Stone colour consistency | Graded by eye under D65 | Colour matched to a retained master stone, per tray | Repeat colour complaint in the same SKU |
| Sizing drift across the run | Not measured | Go/no-go gauge on every size, drift held under 0.15 mm | Resize queue and reship cost |
Nothing here adds cost at USD 60-336. It adds documentation, and documentation is what the retail box with care card carton is missing.
Terms Behind a Vermeil Upgrade Order
The commercial frame is short enough to state in full. Minimum order is 50 pieces per design, and mixed designs travel in one shipment, so a 100-piece Vermeil Upgrade order can carry three or four models without a separate setup charge. Sample pieces leave in 3-5 days when the components are in stock, and a new model adds about twenty days before the first article exists, with GRA report and retail box with care card stated on the same sheet.
Payment is 30 percent with the order and 70 percent against the bill of lading, with the balance window stated on the invoice rather than agreed by message. Prices quoted at USD 60-336 are FOB Guangzhou or Shenzhen; DDP is quoted separately because the duty line moves with the tariff schedule and not with our cost.
Packing follows the retail box with care card format at 100 pieces to the carton, and the packing list carries SKU, size and stone size so receiving can count without opening every box. Private-label cartons add three days for the print run and must be approved before the first bulk order, not after it, with GRA report and retail box with care card stated on the same sheet.
Certification is GRA report for the lots that carry it, with a batch report and per-piece measurement of stone retention after a 40-cycle wear test for the lots below the threshold. The document set travels with the shipping papers, which is what a customs broker asks for at the port rather than after clearance, priced at USD 60-336 for the 100-piece Vermeil Upgrade run.
A rejected tray is settled inside the same order cycle against the retained reference piece. If the difference sits on our retained sample we replace or credit; if it appeared in transit we split the assay cost and file with the carrier, and that rule is written on the order before the deposit clears, which is how the Vermeil Upgrade account reads it at USD 60-336.
Carton Cube, Duty and the Freight Line That Surprises Buyers
The answer for sizing Guide depends on four variables, and three of them are under the buyer's control, quoted at USD 60-336 per piece in retail box with care card.
We run this check per tray rather than per carton because the defect that matters on sizing Guide is the one that repeats. A single odd piece is noise; a pattern across one tray is a process problem and it will be in every tray made after it, priced at USD 60-336 for the 100-piece Vermeil Upgrade run.
The report the buyer receives states the count per tray, the measured average and the outlier count for sizing Guide. It is deliberately unglamorous, and it is the document that settles most disputes before they start, on a 100-piece Vermeil Upgrade order at USD 60-336.
Alloy, Karat and the Cost of a Color Change
In the American bridal market, this is the single most negotiated line on sizing Guide and the least documented one, which is how the Vermeil Upgrade account reads it at USD 60-336.
The buyers who get the most out of sizing Guide treat the first order as a measurement, not as a purchase. They buy a small run, measure the four numbers that matter, and then commit, priced at USD 60-336 for the 100-piece Vermeil Upgrade run.
We support it directly on sizing Guide: a 50-piece test run per design, the same gauge standard as a bulk order, and the same retained tray. Small does not have to mean loose, which is how the Vermeil Upgrade account reads it at USD 60-336.
Getting retail box with care card to the American bridal market
For a Vermeil Upgrade order at 100 pieces the carton count decides the freight more than the weight does. retail box with care card packs tighter than a display tray, the figure being USD 60-336 for a 100-piece run.
The freight rate matters less than the clearance terms at USD 60-336 per piece. A duty surprise can cost more than the entire freight line.
At receiving, count cartons, weigh one tray of retail box with care card and measure ten pieces against stone retention after a 40-cycle wear test. Twenty minutes here saves a season, which is USD 60-336 on the Vermeil Upgrade schedule.
The Calendar Behind a Vermeil Upgrade Run
The calendar below is what we quote on a 100-piece run of sizing Guide. It starts when the spec is signed, not when the deposit clears, with GRA report and retail box with care card stated on the same sheet.
- Sign the drawing at 1:1 scale with a millimetre grid, not a phone render.
- Cut the model in wax or resin and photograph it on the gauge before metal is committed.
- Cast the first article, set the stones and finish it exactly as bulk will be finished.
- Send the first article for approval with the weight and the stone measurements stated.
- Run the balance of the order in 25-30 days, holding the approved article as the reference.
- Ship with the approved article photographed beside a production piece from the same tray.
MOQ stays at 50 pieces per design on the Vermeil Upgrade program, low enough to test a category and high enough to keep the casting line accountable, quoted at USD 60-336 per piece in retail box with care card.
The First Vermeil Upgrade Order
The first order should be small enough to inspect completely and large enough to keep the gauge check independent of the shift, which is how the Vermeil Upgrade account reads it at USD 60-336.
Sample in 3-5 days, bulk in 15-20 days under 500 pieces. At 100 pieces the calendar is the same on every Vermeil Upgrade run, certified GRA report and packed retail box with care card at 100 pieces.
Frequently Asked Questions
How long does a reorder of the same sizing Guide take?
With the model, the gauge set and the signed spec already in our system, a repeat is 12-15 days; a first run is 3-5 days for a stock-component sample and about 20 days when a new model is needed, and 100 pieces leaves Wuzhou in retail box with care card at USD 60-336.
What finish do you use, and how thick is it?
Rhodium at 0.20 micron minimum on white sizing Guide, with a palladium strike layer so wear-through reads white rather than yellow. Vermeil runs at 3 microns over sterling and is logged per lot, which the Vermeil Upgrade file records at USD 60-336 in retail box with care card.
How is sizing Guide packed for retail box with care card?
Every unit goes into a foam-backed pouch, then the retail box with care card, then the outer carton at 100 pieces. The packing list carries the SKU, the size and the stone size so receiving can check without opening every box, and the Vermeil Upgrade quote for it sits at USD 60-336.
Can you ship DDP?
DDP is available for US accounts and removes the duty invoice that arrives after the carton clears. FOB Guangzhou or Shenzhen is the default, and most buyers take DDP once and then switch after they see the breakdown, certified GRA report and packed retail box with care card at 100 pieces.
How long does a reorder of the same sizing Guide take?
With the model, the gauge set and the signed spec already in our system, a repeat is 12-15 days; a first run is 3-5 days for a stock-component sample and about 20 days when a new model is needed, and 100 pieces leaves Wuzhou in retail box with care card at USD 60-336.
Next Step
Send one drawing or one competitor sample with your target landed cost. We answer with a tolerance sheet, a cost breakdown and a production calendar in two business days, quoted at USD 60-336 per piece in retail box with care card.
HOLYCOME runs this line from Wuzhou, Guangxi, through Wuzhou HengliLai Jewelry Co., Ltd. Output is about 60,000 pieces a month across sizing Guide and adjacent categories. service@holycome.com or WhatsApp +86 18078079070, and at USD 60-336 for 100 pieces that is the number the buyer signs.
Related reading: Sizing Guide Amazon FBA Ready: AQL, Tray Checks and What a QC Report Should Say - HOLYCOME Industry Insights Made to Order: What the Quote Actually Covers - HOLYCOME
